Copper weight is the specification buyers most often copy from a previous project and least often re-check. It sounds like a simple number — 1 oz, 2 oz — but it silently changes minimum trace width, etch tolerance, impedance, lamination pressure and price.
This guide converts copper weight into the numbers that matter, explains what changes when you move from 1 oz to 2 oz and beyond, and shows how to specify it so the quote matches the build.
Copper Weight in Microns
Copper weight is quoted in ounces per square foot of foil, which converts to thickness:
| Copper weight | Thickness (approx.) | Typical use |
|---|---|---|
| 0.5 oz | ~17.5 µm | Inner layers of multilayer boards; fine-line designs |
| 1 oz | ~35 µm | The industry default, outer and inner |
| 2 oz | ~70 µm | Power boards, higher current, better heat spreading |
| 3 oz | ~105 µm | Heavy power, motor drives, high-current bus |
| 4 oz | ~140 µm | Heavy copper; specialist fabrication |
| 6 oz and above | ~210 µm and up | Extreme current; quoted as a specialist project |
How thick is 0.5 oz of copper on a PCB? About 17.5 µm, roughly half the standard 1 oz.
How thick is 4 oz of copper on a PCB? About 140 µm, four times the standard.
Note that these are nominal foil thicknesses. After plating, the finished copper on an outer layer is thicker than the starting foil, and the amount depends on the plating process. If you need the finished thickness guaranteed, state it explicitly.
What Are the Differences Between 1 oz and 2 oz Copper PCBs?
Four differences, only one of them obvious
Four differences, and only the first is obvious:
- Current capacity. Doubling copper thickness roughly halves the resistance of a given trace, so a trace can carry more current at the same temperature rise — or the same current with less heating.
- Minimum trace width and spacing. Etching thicker copper is harder. A fabricator holding 4/4 mil at 1 oz may only hold 6/6 mil at 2 oz. The design rules change, not just the number.
- Impedance. Thicker copper slightly lowers impedance and changes the effective trace geometry. On controlled-impedance designs, copper weight is part of the calculation.
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Heavy copper spreads heat laterally, which matters under power devices and in LED boards. A 2 oz inner layer can replace part of a heatsink's job.
3. Mechanical and via reliability. Thicker copper improves mechanical robustness but makes drilling and plating harder, and can reduce annular ring margins.
Then check the constraint: does the fabricator support your minimum feature size at that copper weight? This is the question that changes quotes.
Where Copper Weight Interacts With Everything Else
Five interactions to re-check
With impedance. If the design is impedance-controlled, the copper weight in the calculation must be the finished copper, not the foil.
With fine pitch. Fine-pitch components need thin traces. Heavy copper and fine pitch compete directly, and the compromise is usually a mixed stack-up: heavy copper on inner power layers, standard on outer signal layers.
With metal-core boards. On an aluminum or copper MCPCB, the copper circuit layer and the dielectric are part of one thermal stack. Heavy copper helps spread heat, but the dielectric thickness still dominates.
With vias. Heavy copper plating changes hole diameter and aspect ratio. If your design uses heavy copper and small vias together, confirm both.
With panel utilisation. Heavy copper etches with more variation, so the fabricator may add margin around features, reducing the usable area.
How Much Does a PCB Weigh?
There is no single answer — it depends on area, layer count, copper weight and substrate density. But you can estimate it:
- Substrate: FR4 is roughly 1.8–1.9 g/cm³. A 100 × 100 mm, 1.6 mm board is about 16 cm³, so roughly 29 g of laminate.
- Copper: 1 oz copper is about 305 g/m² per layer. A 100 × 100 mm board with two 1 oz layers carries about 6 g of copper; a six-layer board with four inner layers adds more.
- Finish and mask: a small contribution, a few grams.
For shipping and mechanical design, the practical approach is to ask the fabricator for the calculated weight per panel and per board. For a metal-core board, the metal base dominates: aluminum at 2.7 g/cm³ versus copper at 8.9 g/cm³ is why copper-core boards feel disproportionately heavy.
How to Specify Copper Weight on a Drawing
Write it per layer, and state whether it is nominal foil or finished copper:
Plaintext
L1 (outer): 1 oz finished
L2 (inner): 1 oz
L3 (inner): 2 oz
L4 (outer): 1 oz finished
Two additional notes that prevent surprises:
- Minimum trace/space at this copper weight: state your design's minimum so the fabricator can confirm capability before quoting.
- Heavy copper areas: if a specific region needs 4 oz for current, say where. Uniform 4 oz across a board is more expensive than a local heavy-copper build.
Heavy Copper: When It Is a Project, Not a Specification
Above roughly 3 oz, fabrication moves from "standard with a parameter" to "specialist project". Expect:
- Different etch and plating processes
- Reduced minimum feature sizes
- Longer lead times and higher setup cost
- More DFT (design for test) constraints, because probing heavy copper is different
- Potential need for a stepped or local heavy-copper approach instead of uniform thickness
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits or cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. Many designs specify 2 oz and leave inner layers at 0.5 oz by default. If inner layers carry power, this is the wrong default.
Ignoring impedance. A copper weight change invalidates a previous impedance calculation. Recalculate.
Assuming heavier copper always helps thermal. It helps spreading; it does not help if the dielectric is the bottleneck.
Not asking about the cost step. The jump from 1 oz to 2 oz is modest; from 2 oz to 4 oz can double the board price. Ask before designing to it.
Specification Checklist
- Calculate required trace width for your current and acceptable temperature rise.
- Decide copper weight per layer, not globally.
- Confirm the fabricator's minimum trace/space at that weight, before finalising layout.
- Recalculate impedance if the weight changed.
- State nominal versus finished copper on the drawing.
- Mark local heavy-copper areas if only part of the board needs them.
- Ask for the price step at each weight before committing.
- For metal-core boards, specify the copper circuit layer separately from the base metal.
FAQ
Is 2 oz copper better than 1 oz?
For current capacity and heat spreading, yes. For fine-pitch routing, no — heavier copper etches less precisely, so minimum trace and spacing widen by roughly a capability class. Most designs that need both solve it with a mixed stack-up: heavy copper on inner power layers, standard on outer signal layers.
Does heavier copper always improve thermal performance?
Only where spreading is the bottleneck. If the limiting element is the dielectric layer, as it usually is on a metal-core board, extra copper changes the spreader and leaves the constraint untouched. Copper helps when heat must travel laterally across the board.
How much does copper weight add to the price?
Modestly from 1 oz to 2 oz, steeply beyond that. Above roughly 3 oz the order becomes a specialist project: different etch and plating processes, wider minimum features, longer lead time. Ask for the step price before you design to it, not after.
Can I use 2 oz copper and keep my 1 oz design rules?
No. The traces will not etch reliably at the finer geometry, and the failure appears as opens or near-opens at final test. Re-run the design rules against the actual copper weight, then confirm the fabricator's minimum feature size at that weight.
Why YC PCB
- 20+ years of PCB manufacturing across FR4, aluminum and copper metal-core, multilayer (6–32 layer route), HDI, FPC and rigid-flex
- Heavy copper multilayer constructions reviewed as projects, with minimum feature size confirmed before layout sign-off
- Impedance control recalculated per copper weight, with coupons on request
- DFM review that checks copper weight against your minimum trace and pad geometry
- AOI and electrical test on bare boards; X-Ray, ICT and FCT for assembly projects
- ISO 9001 and UL certification; RoHS compliance documentation on request
- No MOQ / No MOV on standard boards, quoted per project for heavy copper
Get a Quote — Send your Gerber, the copper weight per layer and your current requirement. Our engineers reply with capability confirmation, DFM notes and pricing within one working day.
