Differential pair design guides explain the physics: two traces carrying equal and opposite signals, the receiver taking the difference, common-mode noise rejected. All correct. What they rarely explain is that the pair's impedance is a fabrication outcome — determined by trace width, gap, dielectric thickness and Dk, none of which the designer fully controls alone.
This article covers the handoff: what a fabricator needs to build a differential pair to your target, and where the design decisions become manufacturing constraints. YC PCB builds impedance-controlled multilayer and HDI boards and reviews differential routing on every high-speed project.
The Basics, Briefly
A differential pair is two traces routed together carrying a signal and its complement. The receiver subtracts one from the other, so noise coupled equally into both traces cancels.
Two impedance numbers matter:
- Differential impedance (Zdiff) — the impedance of the pair as a system, typically 90 Ω or 100 Ω
- Single-ended impedance (Z0) — the impedance of each trace to its reference plane, typically around 50 Ω
They are related but not independent: changing the gap changes both.
Coupling: Edge-Coupled vs Broadside
Four configurations and when each is right
| Configuration | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Преимущество | Constraint |
|---|---|---|---|
| Edge-coupled microstrip | Two traces side by side on an outer layer | Simple, easy to route, easy to probe | Impedance depends on gap, which is hard to control tightly |
| Edge-coupled stripline | Two traces side by side on an inner layer between planes | Better shielding, lower emissions | Needs two reference planes |
| Broadside coupled | Two traces stacked on adjacent layers | Tight coupling in less area | Requires specific layer assignment; harder to route |
| Uncoupled (loosely coupled) | Wide spacing, each trace mostly single-ended | Less sensitive to gap tolerance | Larger area; less common-mode benefit |
Practical guidance: edge-coupled stripline is the default for high-speed digital inside a multilayer board. It has a defined reference plane above and below, which controls impedance and contains fields.
The Numbers Your Fabricator Needs
| Input | Why it matters |
|---|---|
| Zdiff target and tolerance | Without a target, the pair is not controlled |
| Z0 target (if specified) | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits |
| Copper weight | Affects geometry and impedance |
| Layer transitions | Where the pair changes reference layer |
| cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits | Verification method |
A note saying "100 ohm differential" with no reference plane and no coupling configuration is not enough to build to.
Length Matching: The Tolerance That Gets Over-Applied
Converting skew into millimetres
Intra-pair skew (the length difference between the two traces of a pair) matters because it converts part of the differential signal into common mode. The practical limits:
- Under about 5 ps of skew is negligible for most designs — roughly 0.7 mm in FR4 at typical propagation velocity
- 5–15 ps is usually acceptable with margin
- Beyond that, check whether the protocol's timing budget actually cares
Since most layout tools show length rather than time, the conversion is worth keeping at hand. In FR4 at typical propagation velocity, 1 ps corresponds to roughly 0.15 mm of trace:
| Skew budget | Equivalent length difference (FR4) | Practical reading |
|---|---|---|
| 1 ps | ~0.15 mm | Over-matching territory; adds capacitance for no benefit |
| 5 ps | ~0.75 mm | Negligible for most protocols |
| 10 ps | ~1.5 mm | Usually acceptable with margin |
| 15 ps | ~2.25 mm | Acceptable for slower interfaces; check the protocol |
| 25 ps and above | ~3.75 mm or more | Only for interfaces whose timing budget accommodates it |
The common error is over-matching: adding serpentine length to hit an arbitrary 0.1 mm tolerance, which adds parasitic capacitance and can degrade the very signal being protected. Match to the protocol requirement, not to a round number.
Inter-pair skew (matching between different pairs, e.g. a parallel bus) is a separate requirement and usually larger.
Where Differential Pairs Fail in Fabrication
Gap tolerance. Etching controls the gap, and gap directly sets Zdiff. A tightly coupled pair with a 0.15 mm gap demands tighter etch control than the same board's single-ended traces. If the target is tight, the gap should be generous.
Dielectric thickness tolerance. The dominant term. A ±10% variation in dielectric thickness produces a meaningful impedance shift, which is why stack-up control matters more than trace width control.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits. A pair that separates to route around a via or a connector has a local impedance change and a skew. Both need to be accounted for.
What to Confirm Before Fabrication
- The stack-up supports the geometry. Give the fabricator your intended width and gap, and ask whether the stack-up can achieve the target within tolerance.
- The reference planes are continuous under the pair, including at transitions.
- Return vias exist wherever the pair changes reference layer.
- The coupon design mirrors production geometry — same width, same gap, same layer.
- The tolerance is achievable. ±10% is common; ±5% requires tighter control of dielectric thickness and etch, and should be discussed before it is specified.
- The measurement method is agreed — TDR, with acceptance criteria and a report.
Where Most Differential Pair Guides Stop
They explain coupling but not cost. Tight coupling requires tighter etch control, which affects yield and price. Loosely coupled pairs are cheaper to build to the same impedance tolerance.
They ignore the stack-up. The impedance equation has dielectric thickness in it. A design calculated on one stack-up and built on another is a different board.
They treat length matching as free. Serpentine routing consumes area and adds capacitance. Over-matching is a real design cost.
They ignore test. Without a coupon, "controlled impedance" is an intention. With a coupon and a TDR report, it is a verified specification.
They assume the fabricator will catch a plane split. DFM review checks manufacturability, not signal integrity. Plane continuity is a design responsibility.
Design-to-Order Checklist
- Define Zdiff (and Z0 if constrained) with a tolerance per net class.
- Choose the coupling configuration and state it.
- Assign the reference plane for each routing layer, and keep it continuous.
- Route with a gap the fabricator can hold at your target impedance.
- Add return vias at every reference-layer transition.
- Match intra-pair length to the protocol requirement, not to an arbitrary number.
- Keep tuning local, and avoid long parallel serpentine sections.
- Send the stack-up, impedance table and coupon requirement with the order.
- Ask the fabricator to confirm the geometry against the stack-up before tooling.
- Request a TDR report on the first lot if the design is marginal.
Часто задаваемые вопросы
Does a differential pair need a reference plane?
Yes. Differential impedance is defined relative to the planes above and below the pair, and each trace still returns current. A pair routed with no continuous reference plane is not impedance-controlled in any useful sense, and it will radiate.
How tight should intra-pair length matching be?
Match to the protocol, not to a round number. Under about 5 ps — roughly 0.75 mm in FR4 — skew is negligible for most interfaces. Chasing 0.1 mm adds serpentine capacitance and can make the signal worse than leaving a small, harmless mismatch.
Is tighter coupling better?
Not automatically. Tight coupling needs tighter etch control to hold the gap, which costs yield, and it makes the pair more sensitive to the plane beneath it. Loosely coupled pairs are often easier and cheaper to build to the same impedance tolerance.
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
Why YC PCB
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
- cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits
- DFM review before tooling, checking the drawing against the stack-up
- AOI and electrical test on bare boards; X-Ray, ICT and FCT for assembly projects
- ISO 9001 and UL certification; RoHS compliance documentation on request
Get a Quote cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https://developers.cloudflare.com/workers/wrangler/configuration/#limits.
