{"id":4281,"date":"2026-11-08T09:50:16","date_gmt":"2026-11-08T09:50:16","guid":{"rendered":"https:\/\/ycpcbs.com\/pcb-stiffener\/"},"modified":"2026-11-10T03:08:28","modified_gmt":"2026-11-10T03:08:28","slug":"pcb-stiffener","status":"publish","type":"post","link":"https:\/\/ycpcbs.com\/fr\/pcb-stiffener\/","title":{"rendered":"cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits"},"content":{"rendered":"<p>A stiffener is a rigid layer bonded to a <a href=\"https:\/\/ycpcbs.com\/fr\/flexible-pcb-design-guide\/\">flexible<\/a> circuit to give local mechanical support. It exists because flex has one structural weakness: <strong>it cannot hold anything that needs to be pushed, pulled or inserted.<\/strong> A connector on unsupported flex peels off. A test pad on unsupported flex deforms under a probe. A component on unsupported flex cracks at the joint.<\/p>\n<p>The decision is not whether to use a stiffener. It is <strong>where it goes, what it is made of, and how thick<\/strong> \u2014 and each of those has a failure mode if chosen carelessly.<\/p>\n<p><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/ycpcbs.com\/wp-content\/uploads\/2026\/07\/Rigid-Flex-PCB-Capability.png\" alt=\"cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits\" width=\"1024\" height=\"576\" \/><\/p>\n<h2>What Is the Purpose of a Stiffener?<\/h2>\n<p>Four functions, in order of frequency:<\/p>\n<ol class=\"post-list\">\n<li><strong>Connector support<\/strong> \u2014 a ZIF, board-to-board or card-edge connector needs a rigid backing so insertion force does not delaminate the flex.<\/li>\n<li><strong>Component mounting<\/strong> \u2014 SMT parts on flex need local rigidity, both for placement and for thermal cycling.<\/li>\n<li><strong>Test pad support<\/strong> \u2014 probe pressure deforms unsupported flex, causing intermittent contact and pad damage.<\/li>\n<li><strong>Assembly handling<\/strong> \u2014 a stiffened area gives the pick-and-place and fixture something to grip.<\/li>\n<\/ol>\n<p>A stiffener is not a heat spreader (though aluminum can serve that role), and it is not a substitute for a proper rigid section in a rigid-flex design.<\/p>\n<h2>Material Options<\/h2>\n<h3>Choose by function, not by habit<\/h3>\n<table>\n<thead>\n<tr>\n<th>Material<\/th>\n<th>Thickness range<\/th>\n<th>Stiffness<\/th>\n<th>Best for<\/th>\n<th>Watch out for<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>FR4<\/td>\n<td>0.1\u20131.6 mm<\/td>\n<td>Rigid, moderate CTE<\/td>\n<td>General connector and component support; lowest cost<\/td>\n<td>CTE mismatch with polyimide flex over wide temperature ranges<\/td>\n<\/tr>\n<tr>\n<td>Polyimide (PI)<\/td>\n<td>0.05\u20130.5 mm<\/td>\n<td>Semi-rigid, thin<\/td>\n<td>Thin stacks, dynamic applications, close CTE match to flex<\/td>\n<td>Less stiff; may not hold a heavy connector<\/td>\n<\/tr>\n<tr>\n<td>Stainless steel<\/td>\n<td>0.1\u20130.3 mm<\/td>\n<td>Very stiff, thin<\/td>\n<td>Tight spaces needing high stiffness; shielding<\/td>\n<td>Conductive \u2014 needs insulation; harder to process<\/td>\n<\/tr>\n<tr>\n<td>Aluminum<\/td>\n<td>0.2\u20131.0 mm<\/td>\n<td>Stiff, good thermal<\/td>\n<td>Thermal spreading plus support; LED and power flex<\/td>\n<td>Conductive; CTE mismatch; weight<\/td>\n<\/tr>\n<tr>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<td>0.2\u20131.0 mm<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits <strong>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/strong> cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits.<\/p>\n<h2>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/h2>\n<h3>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/h3>\n<ul class=\"post-list\">\n<li><strong>Keep the stiffener edge at least one bend radius from the bend line.<\/strong> A rigid edge next to a flexible zone concentrates all strain at the boundary \u2014 the most common stiffener-related failure.<\/li>\n<li><strong>Cover the connector footprint fully<\/strong>, plus a margin. A stiffener that ends mid-connector creates a hinge where the connector body meets the flex.<\/li>\n<li><strong>Do not bridge two separate bend regions<\/strong> with one stiffener. You will create a rigid beam between two hinges and stress both.<\/li>\n<li><strong>Account for adhesive flow.<\/strong> The bonding adhesive squeezes out during lamination, and the effective stiffener area is slightly larger than the drawn area.<\/li>\n<li><strong>Consider both sides.<\/strong> Stiffeners on both sides move the neutral axis and change bending behaviour; on one side they create asymmetric stress.<\/li>\n<li><strong>Leave a clear boundary in the drawing.<\/strong> The fabricator needs the stiffener area as a defined region with material and thickness, not as a note saying \"reinforce here\".<\/li>\n<\/ul>\n<h2>Connector Scenario Decision Table<\/h2>\n<table>\n<thead>\n<tr>\n<th>Sc\u00e9nario<\/th>\n<th>Stiffener approach<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>ZIF connector, insertion force along the flex<\/td>\n<td>FR4 or PI stiffener under the contact area, extending past the connector body<\/td>\n<\/tr>\n<tr>\n<td>Board-to-board connector, repeated mating<\/td>\n<td>Stiffener on the connector side, thickness matched to the mating height; consider both sides<\/td>\n<\/tr>\n<tr>\n<td>Card-edge contact (gold fingers)<\/td>\n<td>Stiffener behind the contacts, thickness set by the mating slot; hard gold on the contact side<\/td>\n<\/tr>\n<tr>\n<td>SMT components near the connector<\/td>\n<td>Extend the stiffener to cover both, or use two stiffeners with a defined gap<\/td>\n<\/tr>\n<tr>\n<td>Test pads only<\/td>\n<td>Thin PI stiffener is usually enough; FR4 if probe pressure is high<\/td>\n<\/tr>\n<tr>\n<td>Dynamic bend near a connector<\/td>\n<td>Stiffener must end at least a bend radius away; consider a longer flexible region instead<\/td>\n<\/tr>\n<tr>\n<td>Thermal load (LED or power on flex)<\/td>\n<td>Aluminum stiffener can double as a spreader, with insulation between<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>What to Specify for a Quote<\/h2>\n<table>\n<thead>\n<tr>\n<th>Item<\/th>\n<th>Detail<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Stiffener material<\/td>\n<td>FR4, PI, stainless steel, aluminum, or a specific grade<\/td>\n<\/tr>\n<tr>\n<td>Thickness<\/td>\n<td>Per stiffener, and the resulting total stack height<\/td>\n<\/tr>\n<tr>\n<td>Area<\/td>\n<td>A defined region on the drawing, with dimensions<\/td>\n<\/tr>\n<tr>\n<td>Side<\/td>\n<td>Top, bottom, or both<\/td>\n<\/tr>\n<tr>\n<td>Adhesive type<\/td>\n<td>If the application has temperature or outgassing constraints<\/td>\n<\/tr>\n<tr>\n<td>Surface finish on the stiffener<\/td>\n<td>If exposed (materials handling, marking)<\/td>\n<\/tr>\n<tr>\n<td>Total thickness at the stiffener<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<tr>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<tr>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<tr>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits <strong>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/strong>. Connector mating dimensions depend on it, and a 0.2 mm error is a mechanical failure.<\/p>\n<h2>Where Stiffener Designs Fail<\/h2>\n<p><strong>Edge at the bend.<\/strong> Already stated, and still the most common. It happens because the stiffener area is drawn from the connector outline rather than from the bend line.<\/p>\n<p><strong>Ignoring adhesive thickness.<\/strong> A 0.2 mm stiffener with 25 \u00b5m adhesive adds more than 0.2 mm to the stack. Multiply across a tolerance chain and the connector no longer mates.<\/p>\n<p><strong>Stainless steel without insulation.<\/strong> Stainless is conductive. If it sits over exposed traces or vias, you have a short waiting to happen.<\/p>\n<p><strong>Stiffener over a via.<\/strong> A via under a stiffener cannot be inspected or reworked, and the adhesive may not fill around it. Keep vias out of the stiffened area where possible.<\/p>\n<p><strong>Assuming stiffness equals flatness.<\/strong> A stiffener can lock in a warp if the lamination is not flat. For precision assemblies, ask about flatness after stiffening.<\/p>\n<p><strong>No finish specified on an exposed stiffener.<\/strong> An exposed FR4 stiffener with bare copper will oxidise; an exposed aluminum stiffener will scratch and corrode.<\/p>\n<h2>Design-to-Order Checklist<\/h2>\n<ol class=\"post-list\">\n<li>Identify every location needing support: connectors, components, test pads, handling areas.<\/li>\n<li>Choose material by function \u2014 mechanical, thermal, or electrical.<\/li>\n<li>Set thickness from the mating dimension, not from what is in stock.<\/li>\n<li>Place every stiffener edge at least one bend radius from any bend line.<\/li>\n<li>Draw the stiffener area explicitly, with dimensions and side.<\/li>\n<li>State total stack thickness at the stiffener.<\/li>\n<li>Confirm adhesive type if temperature or outgassing matters.<\/li>\n<li>Keep vias and exposed traces out of stiffened regions, or insulate.<\/li>\n<li>Specify finish for any exposed stiffener surface.<\/li>\n<li>Confirm flatness requirement after stiffening for precision assemblies.<\/li>\n<\/ol>\n<h2>FAQ<\/h2>\n<h3>What is a rigid-flex PCB?<\/h3>\n<p>A board built as one continuous stack-up with rigid sections (components, vias) and flexible sections (interconnect). In rigid-flex, the rigid sections are laminated structures, not bonded stiffeners \u2014 a distinction that matters for cost and reliability.<\/p>\n<h3>What does PCB stand for?<\/h3>\n<p>Printed Circuit Board. \"Printed\" refers to the additive\/subtractive patterning of copper rather than drawn wiring.<\/p>\n<h3>Is a stiffener the same as a rigid section?<\/h3>\n<p>No. A stiffener is a separate piece bonded onto a finished flex; a rigid section is built into the stack-up during lamination. Stiffeners are cheaper and faster to change, rigid sections are more reliable and can carry vias. Choosing one when the design needs the other is a common and expensive mistake.<\/p>\n<h3>Can a stiffener be added after the flex is built?<\/h3>\n<p>Sometimes, for prototypes, but it is not a production approach. Adhesive bonding after the fact gives less control over flatness, adhesive thickness and registration, and the bond strength is lower than a laminated stiffener. Specify it on the drawing and let it be built in.<\/p>\n<h2>Why YC PCB<\/h2>\n<ul class=\"post-list\">\n<li>20+ years of PCB manufacturing including FPC and rigid-flex, with double-layer and 4-layer flex constructions<\/li>\n<li>Stiffener material, thickness and area confirmed at DFM review, with bend-line clearance checked<\/li>\n<li>Coverlay, stiffener and connector interface reviewed together, because they interact<\/li>\n<li>ENIG and hard gold finishes for contact areas<\/li>\n<li>AOI and electrical test on bare boards; X-Ray, ICT and FCT for assembly projects<\/li>\n<li>ISO 9001 and UL certification; NDA available for customer IP<\/li>\n<\/ul>\n<p><a href=\"https:\/\/ycpcbs.com\/fr\/contact\/\"><strong>Get a Quote<\/strong><\/a> \u2014 Send your Gerber, layer structure, stiffener material and thickness, connector specification and bend requirements. Our engineers reply with DFM notes, material options and pricing within one working day.<\/p>\n<h2>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/h2>\n<ul class=\"post-list\">\n<li><a href=\"https:\/\/ycpcbs.com\/fr\/rigid-flex-pcb-design-guide\/\">rigid-flex design rules<\/a><\/li>\n<li><a href=\"https:\/\/ycpcbs.com\/fr\/flexible-pcb-vs-rigid-flex-pcb\/\">flex vs rigid-flex<\/a><\/li>\n<li><a href=\"https:\/\/ycpcbs.com\/fr\/flexible-pcb-fpc-rigid-flex\/\">flexible PCB fabrication<\/a><\/li>\n<\/ul>","protected":false},"excerpt":{"rendered":"<p>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits.<\/p>","protected":false},"author":1,"featured_media":3968,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[99],"tags":[],"class_list":["post-4281","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-flexible-rigid-flex-pcb"],"_links":{"self":[{"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/posts\/4281","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/comments?post=4281"}],"version-history":[{"count":1,"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/posts\/4281\/revisions"}],"predecessor-version":[{"id":4310,"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/posts\/4281\/revisions\/4310"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/media\/3968"}],"wp:attachment":[{"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/media?parent=4281"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/categories?post=4281"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/ycpcbs.com\/fr\/wp-json\/wp\/v2\/tags?post=4281"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}