{"id":4277,"date":"2026-11-08T09:50:16","date_gmt":"2026-11-08T09:50:16","guid":{"rendered":"https:\/\/ycpcbs.com\/hdi-pcb-design-checklist\/"},"modified":"2026-11-10T03:08:27","modified_gmt":"2026-11-10T03:08:27","slug":"hdi-pcb-design-checklist","status":"publish","type":"post","link":"https:\/\/ycpcbs.com\/de\/hdi-pcb-design-checklist\/","title":{"rendered":"HDI PCB Design Review Checklist: Microvias, Stack-Up, BGA Escape and Impedance"},"content":{"rendered":"<p>HDI boards fail review for predictable reasons: a microvia aspect ratio the process cannot hold, a stack-up that needs one more lamination cycle than was quoted, a BGA escape that assumes a via pitch the fabricator cannot drill, or an impedance target with no reference plane under it.<\/p>\n<p>This checklist is written for the review that happens <strong>before<\/strong> the board goes to quotation \u2014 the point where a change costs an hour instead of a re-spin. YC PCB builds HDI up to 20-layer FR4 HDI constructions and reviews designs from customers across industrial, communication and automotive programmes.<\/p>\n<p><img loading=\"lazy\" decoding=\"async\" src=\"https:\/\/ycpcbs.com\/wp-content\/uploads\/2026\/05\/Blind-Buried-Via-PCB.png\" alt=\"HDI PCB with blind and buried vias\" width=\"1024\" height=\"576\" \/><\/p>\n<h2>What Is HDI in PCB Design?<\/h2>\n<p>HDI (high-density interconnect) is a construction approach rather than a specific board type. Its defining features:<\/p>\n<ul class=\"post-list\">\n<li><strong>Microvias<\/strong> \u2014 laser-drilled vias, typically 0.1 mm or smaller, connecting adjacent layers<\/li>\n<li><strong>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/strong> \u2014 connections that do not pass through the full board<\/li>\n<li><strong>Sequential lamination<\/strong> \u2014 the board is built in stages, with vias formed between stages<\/li>\n<li><strong>Higher routing density per layer<\/strong> \u2014 finer lines, smaller vias, tighter pitches<\/li>\n<\/ul>\n<p>The purpose is density: more connections in less area, which is what fine-pitch BGA, compact modules and wearable-class products require.<\/p>\n<h2>Checklist 1: Microvia Rules<\/h2>\n<table>\n<thead>\n<tr>\n<th>Parameter<\/th>\n<th>What to confirm<\/th>\n<th>Why it fails otherwise<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Microvia diameter<\/td>\n<td>0.1 mm or as agreed, with tolerance<\/td>\n<td>Below process capability, the via cannot be reliably filled or plated<\/td>\n<\/tr>\n<tr>\n<td>Aspect ratio (depth \u00f7 diameter)<\/td>\n<td>Typically \u2264 1:1 for laser microvias<\/td>\n<td>Deeper than 1:1, plating uniformity drops sharply<\/td>\n<\/tr>\n<tr>\n<td>Dielectric thickness over the via<\/td>\n<td>Matches the laser depth capability<\/td>\n<td>Inconsistent depth causes open or weak connections<\/td>\n<\/tr>\n<tr>\n<td>Via-in-pad fill<\/td>\n<td>Filled and planarised, or the pad must be moved<\/td>\n<td>Unfilled via-in-pad causes voids, wicking and skew at assembly<\/td>\n<\/tr>\n<tr>\n<td>Via-to-via spacing<\/td>\n<td>Meets the minimum for the lamination stage<\/td>\n<td>Too close causes resin starvation between vias<\/td>\n<\/tr>\n<tr>\n<td>Capture pad diameter<\/td>\n<td>Large enough for laser registration tolerance<\/td>\n<td>Small capture pads break on misregistration<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p>Every microvia in the design should map to a specific lamination stage. If the design uses microvias across more stages than the quoted build, the quote is wrong.<\/p>\n<h2>Checklist 2: Stack-Up and Lamination Sequence<\/h2>\n<p>HDI stack-ups are built in cycles: core, lamination, laser drill, plating, repeat. Each cycle adds cost and lead time, and each cycle introduces registration risk.<\/p>\n<h3>Five things the stack-up drawing must show<\/h3>\n<p>Confirm:<\/p>\n<ol class=\"post-list\">\n<li><strong>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/strong> cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits.<\/li>\n<li><strong>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/strong> cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits.<\/li>\n<li><strong>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/strong> cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits.<\/li>\n<li><strong>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/strong> cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits.<\/li>\n<li><strong>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/strong> \u2014 and how the build-up thicknesses add up to it.<\/li>\n<\/ol>\n<p>A stack-up that is not explicit about cycles cannot be quoted accurately. Ask for the drawing, not the price.<\/p>\n<h2>Checklist 3: BGA Escape Routing<\/h2>\n<h3>Design the escape before the layer count<\/h3>\n<p>BGA escape is where HDI design intent meets fabrication reality.<\/p>\n<ul class=\"post-list\">\n<li><strong>Ball pitch and pad diameter<\/strong> \u2014 determine how many traces can pass between pads<\/li>\n<li><strong>Escape layer<\/strong> \u2014 which layer the first fan-out happens on, and whether it needs microvias<\/li>\n<li><strong>Via-in-pad versus dog-bone<\/strong> \u2014 via-in-pad saves space but requires fill and planarisation<\/li>\n<li><strong>Trace width and spacing at escape<\/strong> \u2014 the tightest geometry on the board, and therefore the yield driver<\/li>\n<li><strong>Power and ground via count<\/strong> \u2014 current capacity and return path, often under-designed at the escape<\/li>\n<\/ul>\n<p>The practical rule: design the escape first, then the rest of the routing. If the escape does not close, the layer count is wrong.<\/p>\n<h2>What Is the 3W Rule in PCB Design?<\/h2>\n<p>The 3W rule says the centre-to-centre spacing between adjacent traces should be at least three times the trace width. It reduces crosstalk between parallel traces \u2014 often quoted as a roughly 70% reduction compared with edge-to-edge spacing equal to one width.<\/p>\n<p>In HDI designs the rule is harder to apply because trace width is already small and density is high. The practical approach is to apply 3W where it matters \u2014 sensitive analogue lines, clock lines, high-impedance nodes \u2014 and to accept tighter spacing elsewhere with a reference plane in place.<\/p>\n<h2>What Is the 3H Rule in PCB Design?<\/h2>\n<p>The 3H rule sets the spacing from a trace to its reference plane (or between traces in a mixed-signal context) at three times the dielectric height. It is used to control field coupling, particularly in mixed-signal and RF layouts.<\/p>\n<p>In an HDI build-up, dielectric height over the microvia layer is small, so 3H translates to a small absolute distance \u2014 which is often why HDI boards are quieter than their geometry suggests. The catch is that the reference plane must be continuous. A split under a sensitive trace defeats the rule entirely.<\/p>\n<h2>Can ChatGPT Do PCB Design?<\/h2>\n<p>No. It can help with documentation, checklist generation, explaining a rule, or drafting a <a href=\"https:\/\/ycpcbs.com\/de\/pcb-dfm-checklist\/\">DFM<\/a> note. It cannot make the engineering trade-offs that decide a stack-up \u2014 and it has no access to your fabrication partner's process windows, material availability or registration capability.<\/p>\n<p>The useful division of labour: use AI to organise the review, use an engineer to make the decisions, and use the fabricator's DFM review to catch what both missed. A design that exists only in a chat log is not a design.<\/p>\n<h2>Checklist 4: Impedance and Reference Planes<\/h2>\n<ul class=\"post-list\">\n<li>Each controlled-impedance net class has a target, a tolerance and a named reference plane<\/li>\n<li>No reference plane splits under controlled traces or across layer transitions<\/li>\n<li>Return vias present wherever a signal changes reference layer<\/li>\n<li>Via stubs considered: on thick HDI builds, back-drilling or blind vias may be required at high frequency<\/li>\n<li>Coupon design agreed, with the same geometry as production traces<\/li>\n<\/ul>\n<h2>Checklist 5: Fabrication and Assembly Inputs<\/h2>\n<h3>What HDI needs that a standard board does not<\/h3>\n<table>\n<thead>\n<tr>\n<th>Input<\/th>\n<th>Why it matters in HDI<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Full stack-up with cycles<\/td>\n<td>Determines cost, lead time and feasibility<\/td>\n<\/tr>\n<tr>\n<td>Microvia table<\/td>\n<td>Diameter, depth, layer pair, fill requirement<\/td>\n<\/tr>\n<tr>\n<td>BGA pitch and pad data<\/td>\n<td>Drives escape and assembly<\/td>\n<\/tr>\n<tr>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<tr>\n<td>Impedance table<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<tr>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<tr>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<tr>\n<td>Assembly drawing<\/td>\n<td>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<h2>cURL Too many subrequests by single Worker invocation. To configure this limit, refer to https:\/\/developers.cloudflare.com\/workers\/wrangler\/configuration\/#limits<\/h2>\n<p><strong>Microvia depth assumed, not specified.<\/strong> The laser depth depends on the dielectric thickness over the target layer. If the stack-up does not fix that thickness, the via depth is not controlled.<\/p>\n<p><strong>Via-in-pad without fill.<\/strong> A via-in-pad that is not filled will wick solder, create voids and cause skew on fine-pitch parts. It is a fill requirement, not a drilling requirement.<\/p>\n<p><strong>Layer count chosen before escape routing.<\/strong> The most common cause of a re-spin: two more layers were needed, and the stack-up was signed off too early.<\/p>\n<p><strong>Impedance specified after stack-up.<\/strong> Impedance follows from the stack-up. Specifying it afterwards means either the stack-up changes or the target is missed.<\/p>\n<p><strong>Test coverage assumed.<\/strong> Microvia boards are dense. If test pads were not designed in, electrical test coverage drops to what the fixtures can reach.<\/p>\n<h2>Review Checklist<\/h2>\n<ol class=\"post-list\">\n<li>Map every microvia to a lamination stage and confirm the count of cycles.<\/li>\n<li>Confirm microvia diameter, depth and aspect ratio against the fabricator's process window.<\/li>\n<li>Decide via-in-pad fill per location and confirm planarisation.<\/li>\n<li>Close the BGA escape before fixing the layer count.<\/li>\n<li>Make the stack-up symmetric in material and copper.<\/li>\n<li>Apply 3W and 3H where they matter, and confirm plane continuity under sensitive traces.<\/li>\n<li>Specify impedance per net class with tolerance and reference planes.<\/li>\n<li>Reserve test access and agree the test method.<\/li>\n<li>Send the full input set: Gerber, drill, stack-up with cycles, via table, impedance table, assembly drawing.<\/li>\n<li>Read the DFM response against the stack-up drawing before approving tooling.<\/li>\n<\/ol>\n<h2>FAQ<\/h2>\n<h3>What counts as an HDI board?<\/h3>\n<p>A board that uses laser-drilled microvias with sequential lamination, so connections are made between adjacent layers rather than through the whole board. Density is the purpose, and the microvia is the marker. A fine-line multilayer with only through-holes is not HDI, however tight the routing.<\/p>\n<h3>How many lamination cycles does an HDI board need?<\/h3>\n<p>One per build-up stage, so a design with microvias on both outer surfaces is typically at least two, and more if buried microvias are used. Each cycle adds cost, lead time and registration risk. The count should be drawn on the stack-up, not inferred from the price.<\/p>\n<h3>Why is via-in-pad a problem if it is not filled?<\/h3>\n<p>Because solder wicks down the open barrel during reflow. That leaves a void under the component, reduces joint volume and can tilt small parts. Filling and planarising is a separate process step, and it has to be specified per via, not assumed as part of drilling.<\/p>\n<h3>Can I add HDI layers later if density is tight?<\/h3>\n<p>Effectively no. Adding a build-up stage changes the lamination sequence, the via structure and often the microvia table. It is a re-spin, which is why the BGA escape should be closed and the layer count confirmed before the stack-up is signed off.<\/p>\n<h2>Why YC PCB<\/h2>\n<ul class=\"post-list\">\n<li>HDI capability including a 20-layer FR4 HDI construction, alongside a 6- to 32-layer rigid route<\/li>\n<li>Microvia, blind and buried via builds reviewed against the stack-up before tooling<\/li>\n<li>Impedance control with coupons and measurement available on request<\/li>\n<li>DFM\/DFA engineering review; NDA available for customer IP<\/li>\n<li>AOI and electrical test on bare boards; X-Ray, ICT and FCT for assembly, with BGA\/QFN\/Micro-BGA support<\/li>\n<li>ISO 9001 and UL certification; RoHS compliance documentation on request<\/li>\n<li>No MOQ \/ No MOV on standard boards, quoted per project for HDI builds<\/li>\n<\/ul>\n<p><a href=\"https:\/\/ycpcbs.com\/de\/contact\/\"><strong>Get a Quote<\/strong><\/a> \u2014 Send your Gerber, drill, stack-up with lamination cycles, via table and impedance targets. Our engineers reply with a feasibility review, DFM notes and pricing within one working day.<\/p>\n<h2>Related reading<\/h2>\n<ul class=\"post-list\">\n<li><a href=\"https:\/\/ycpcbs.com\/de\/multilayer-pcb-design\/\">multilayer stack-up design<\/a><\/li>\n<li><a href=\"https:\/\/ycpcbs.com\/de\/controlled-impedance-pcb-requirements\/\">impedance quote inputs<\/a><\/li>\n<li><a href=\"https:\/\/ycpcbs.com\/de\/hdi-pcb-20-layer-fr4\/\">HDI PCB fabrication<\/a><\/li>\n<\/ul>","protected":false},"excerpt":{"rendered":"<p>An HDI PCB design review checklist for engineers and buyers: microvia rules, stack-up sequencing, BGA escape routing, impedance and the data a fabricator needs.<\/p>","protected":false},"author":1,"featured_media":2534,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[89],"tags":[],"class_list":["post-4277","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-pcb-design"],"_links":{"self":[{"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/posts\/4277","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/comments?post=4277"}],"version-history":[{"count":1,"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/posts\/4277\/revisions"}],"predecessor-version":[{"id":4306,"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/posts\/4277\/revisions\/4306"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/media\/2534"}],"wp:attachment":[{"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/media?parent=4277"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/categories?post=4277"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/ycpcbs.com\/de\/wp-json\/wp\/v2\/tags?post=4277"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}